Wir haben bereits die ersten Details von der neuen Serpent Cobra GT 3.0 1/8 4WD veröffentlicht. An dieser Stelle könnt ihr die ersten Bilder von der Elektroversion der neuen Serpent Cobra GTe 3.0 1/8 4WD sehen. Erste Infos und Details sind weitesgehend mit der Serpent Cobra GT 3.0 1/8 4WD identisch. Hier fehlen nur die Lipo-Akkus, der Brushlessregler und Motor zum Vortrieb. Zur GP, also Verbrennerversion ist das Chassis an die elektronischen Komponenten angepasst und neu. Das Chassis ist für zwei Akkus vorgesehen, die im hinteren Chassisbereich sehr flach eingebaut werden können. Dadurch ist der Schwerpunkt so tief wie möglich. Aufhängung- und Antriebsteile sind außer zwischen den beiden Getrieben (vorn / hinten) in beiden Versionen (EP / GP) identisch.
Englische-Version mit mehr Details am Ende des Beitrags.
Bilder der Serpent Cobra GTe 3.0 1/8 EP 4WD:
Quelle: Serpent
Weitere Infos:
In Deutschland gibt es für solche Fahrzeuge auch eine Rennserie. Wer bei Facebook ist, kann hier sich hier in der Gruppe informieren: –Zur Gruppe–. Wer noch etwas wartet, der kann auch auf der Webseite nachsehen. Diese ist jedoch gerade im Aufbau.
Regelwerk 1:8 Brushless GT Series
1. Chassis: Es sind alle 1:8 GT ( Rallye Game ) Fahrzeuge zugelassen mit einem Mindestradstand von 320 mm. Die Fahrzeuge müssen auf dem Deutschen Markt erhältlich sein, mit einem in Deutschland ansässigem Vertrieb und Ansprechpartner. Die Fahrzeuge müssen die Maße der Hersteller beibehalten und dürfen nur durch Tuningteile der Hersteller oder Zulieferer optimiert werden. Eigenbauten und Riemenangetriebene Fahrzeuge werden nicht zum Start zugelassen.
2. Akkus: Es darf maximal an 4S ( 16,8 Volt ) gefahren werden. Der Einsatz von 7,6V an 2 S und 15,2 V an 4S Akkus ist verboten !!
3. Kreiselsysteme oder andere Fahrhilfen sind nicht erlaubt.
4. Karosserie: Es sind alle Karos der Hersteller oder deren Zulieferer sowie aus dem Zubehör zugelassen. Die Karosserie muss die Typische GT oder DTM Optik haben. Der Heckspoiler darf optimiert werden und auch durch Eigenbauten ersetzt oder aus dem Zubehörmarkt verwendet werden. Lola Karosserien sind nicht erlaubt.
5. Das Fahrzeug darf mit den vom Hersteller oder deren Zulieferer zur Verfügung gestellten Tuningteile optimiert werden. Auch Teile von den anderen Herstellern ,dürfen fürs eigene Fahrzeug benutzt werden. Tuning und Ersatzteile müssen für Jedermann zugänglich und erhältlich sein. Die Reifenwahl ist frei. Die Motorenwahl ist frei. Der Motor darf 2450 KV nicht überschreiten. Der Motor muss offiziell im deutschen Handel für Jedermann erhältlich und bestellbar sein. ( Im Ladenlokal oder sichtbar im Onlineshop )
Die Reglerwahl ist frei. Moosgummireifen sind verboten.
Änderungen möglich!
Englische Version:
Serpent Cobra GTE 3.0 1/8 4wd details
The Serpent Cobra GT is the most popular brand in GT racing and its performance is proven by many big racewins in the highly competitive race scene for GT’s in America. The Cobra GT 3.0 is the latest development stage of the Cobra GT platform, which is running successfully for over 5 year with very small changes only. Below we show the key updates to the GT to continue its strong performance and famous durability.
The Cobra GTE is a combined design effort by Billy Easton and Michael Salven, in cooperation with our USA team-drivers Desoto and Morganti.
Main new features
– New front front and front rear aluminium suspension holders
– New Alu c-hubs in 6 degree version
– New aluminium, uprights for new rear geometry
– New alu shockabsorber risers front and rear
– New 4.5mm carbon shocktowers front and rear
Explaining the new features
New front front and front rear aluminium suspension holders
- These are designed to change the piviot pin angle, so the lower wishbones will be more straight, which geomery suits onroad racing better.
New Alu c-hubs in 6 degree version
- The new alu c-hubs are needed to make maximum use of the new pivit pin / wishbone angle. CNC-machined from 7075 T6 alumnium, laser engraved and black anodised units.
New aluminium, uprights for new rear geometry
To allow a better onorad geometry we desigend these new CNC machined aluminium uprights, black anodised and laser engraved.
New alu shockabsorber risers front and rear
- New alu shocktowers front and rear
The durable machined alu shock-risers front and rear allow for a more onroad aimed angle of the shockabsorber creating more overall grip and more predictable cornering. The new 4.5mm lower carbon fibre shocktowers also accomodate the new shock angles, with a choice of 5 holes for further fine-tuning.
Overall features / specs
Chassisplate
- Chassisplate in 3mm 7075 T6 aluminium , with machined pockets to create flex and or make lighter. Kick-up angle on front as need due to the race-rules. Countersunk holes. Slots to locate the front and rear suspension mounts precisely. Angled sides to increase stiffness Laser engraved Cobra GT logo.
Bumper
- Captured foam bumper set, with wide foam bumper and strong upper and lower bumper-plate.
Chassis stiffners
- Composite stiffner front and rear, to give extra stiffness, but still allow some flex as needed.
Radio-box
- Composite radiobox which offers space for the up-right steering-servo, the receiver and sufficient space for the speed-controller. The whole assembly including linkages can be taken off easily and fast in one go, when cleaning the car, or doing maintenance.The main eyecatchers are the extremely low laydown longtudinal placed battery-packs at each side of the car, being part of the side-guards, securely fastened with a flip-lid, for easy and fast battery changes. The weight low in the car and in the right position, well balanced. The Lipo holders comply with ROAR legal packs / dimensions.
Servo arms and linkages
- The servo arms have a splined insert to have the right fit per brand. The linkages runs very clean and tight and are easy to access to modify settings.
Suspension brackets
- Beautifully machined 7075 T6 suspension brackets in anodized, laser angraved. Pecision fit for the nylon roll center inserts and pivot balls / pins. The GT 3.0 front suspension brackets make the pivot-pin and lower arm more horizontal, which improves handling and steering.
Steeringblocks assembly
- Composite steeringblocks combined with 10 dgr C-hubs for precise steering. Spring steel wheel-axles with large size bearings 8x18x5 and 15x21x4 with precision threaded aluminum wheel-hubs with +3 offset . Flanged wheel nuts to guarantee that you will not loose a wheel nut in a race.
Front suspension
- Durable oversized lower suspension arms in strong composite nylon. On the lower side the special downstops screws are mounted. The lower shock-mounting pins are secured with a small grubscrew from the bottom.
Front anti-roll bar
- The ballraced front anti-roll bar system, consist of a spring steel bend wire, which is guided through the diff-cases and run in ballraced steel adaptors. The wire is linked to the lower suspension arm, with a captured adjustable threaded pivotball, for very precise and low friction operation.
Shocktower and bodymounts front / alu shock-risers
- new 4.5mm thick carbon shocktower with 5 upper positioning holes for the shocks and and 6 holes for roll-center positions. 1 centrally located adjustable bodymount , and 2 forward mounted adjustable bodymounts, all with flip-tops. The durable machined alu shock-risers in front allow for a more onroad aimed angle of the shockabsorber creating more overall grip and more predictable cornering.
Angled steering system / servo saver
- The bell cranks are angled to reduce the angle of difference between the total caster and steering plane. Therefore you will have less bump steer and a truer steering Ackerman through the entire range of suspension
Ackermann plates
- With the design of the steering bell cranks when changing the Ackermann you will not need to adjust your steering tie rods. You simply will only need to adjust your end points on your radio..
Rear suspension arms
- Durable oversized lower suspension arms in strong composite nylon. On the lower side the special downstops screws are mounted. The lower shock-mounting pins are secured with a small grubscrew from the bottom.
Rear uprights assembly
- New alumnium, black anodised and laser engraved uprights with 3 upper roll-center positions. Strong steel track-rods with L/R threading and strong balljoints to pre-set camber. Spring steel wheel-axles with large size bearings 8x16x5 and 13x19x4 with precision threaded aluminum wheel-hubs with +3 offset . Rubber dustcovers in the rear to protect the cvd system and keep the lubrication inside. Flanged wheel nuts to guarantee that you will not loose a wheel nut in a race.
Rear anti-roll bar
- The ballraced front anti-roll bar system, consist of a spring steel bend wire, which is guided through the diff-cases and runs in ballraced steel adaptors. The wire is linked to the lower suspension arm, with a captured adjustable threaded pivotball, for very precise and low friction operation.
Shocktower rear / alu shock-risers
- New 4.5mm thick carbon shocktower, integrated into the rear section for extra stiffness, with 5 upper positioning holes for the shocks and 6 holes for roll-center positions. The durable machined alu shock-risers in the rear allow for a more onroad aimed angle of the shockabsorber creating more overall grip and more predictable cornering.
Wingmount and bodymounts rear
- Composite rear wing, with strong nylon adjustable rear bodymounts on wide body-support bridge located far enough to the rear, to support the bodies in best way.
Captured pivot pins and balls and bolted hinge pins
- All spring-steel hinge pins are either captured or bolted in place and made in spring-steel quality. This insures your chances to finish an hour long main event, while battling for the lead. This relieves stress on the hinge pin when adjusting the kick up, or anti squat. Your pin is free to rotate to any angle without binding.
Shockabsorbers big-bore 16mm
- Hard Teflon coated threaded shockbodies with 4mm shock-rods. Black anodized aluminium screw on shock-tops with Serpent laser engraving. Pre-load adjusters with o-rings inside. Shocks use large diameter membrames and large diameter o-rings and bushings to create a supersmooth and leak-proof package. Large diameter pistons are held in place by a nut on the polished shock-rods tops. Open type spring retainer to let dirt out easy.
RCM shock springs
- Short type colorcoded shock springs are supplied for the 1st standard set-up Springs are grinded flat top and bottom, and checked individually for tension and length.
Compact geardifferentials
- Very compact gear differentials with very smooth metal sintered gears, and steel shaft. Perfect sealing case with special gasket and o-rings. Very light and durable outdrive cups in spring-steel. Hardened spring-steel diff-coupler 13T with connector running in 2 oversized bearings 8x19x6 and ballbearing-13x19x4.
Front and rear cvd-sets
- Both front and rear captured driveshafts are being used with CVD system. Durable yet light spring steel engraved driveshafts with hard steel pins.
Spring steel transmission parts
- The front and rear thin but strong spring steel cardan shafts connect the differentials with the gearbox section.
Motor mount
- Machined 7075 T6 aluminium motor-mount with one-screw fixation and easy slider system. Flex-free and very strong motormount. The space for the motor allows a maximum motor-length of 68mm, which covers most widely used motors.
Oils and grease
- The shock-oil, diff oil and some grease is supplied to meet the standard set-up.
Manual and set-up
- Full color online manual and USB stick version with easy to follow assembly steps, exploded views for easy spares ordering, a blank and standard set-up sheet for a good start set-up.
Decals
- Black and white promo body-decals ; Serpent generic and Cobra GT ones.
Packing
- Parts are packed according to the steps explained in the manual.
Service and Support
- The Serpent distributor, dealer or agent is your source for more info, but also the Serpent website, Facebook-sites and the Youtube channel provides lots of information.
Needed to complete the car
– radio and receiver
– electric motor
– speedcontroller
– Lipo battery packs x 2
– wheels and tyres
– body and wing
– paint
Quelle: Serpent